Empire Products BF-10-2 Owner's Manual download pdf (Page 17)

16943-10-0314 Page 17

INSTALLING OPTIONAL BLOWER SRB-18T OR SRB-30T

If heater is installed onto the wall, in order to install the optional

blower, the heater must be removed from the wall. If heater

is installed on SRS-18 or SRS-30 optional oor stand there is

adequate access area available to install the optional blower.

1. Turn "OFF" gas supply to the heater.

2. Remove lower louver from casing assembly (2 screws).

3. Remove reector from casing assembly (2 screws).

4. Remove upper louver from casing assembly (2 screws).

5. Insert the fan control wires and the upper portion of the fan

control through the 3/4" (19mm) diameter hole on the bottom

side of the top heat shield. The fan control wires will enter into

the top portion of the heater and the fan control disc will be

facing the main burner. Attach fan control to the bottom side of

the top heat shield with (2) screws provided with the optional

blower.

6. Route cord set through 9/16" (14mm) diameter hole on casing

assembly back. Insert approximately 3" (76mm) of cord set

into casing assembly back.

7. When you are facing the front of the heater, position the optional

blower assembly onto the top heat shield of the heater. The

motor wire harness should be facing into the top, right portion

of the heater.

8. Attach (1) pin terminal from black (hot) wire, smooth insulation on

cord set to (1) socket terminal on fan control wire harness.

9. Attach (1) pin terminal from black (neutral) wire, ribbed insula-

tion on cord set to (1) socket terminal from white (neutral) wire

on motor wire harness.

10. Attach (1) pin terminal on fan control wire harness to (1) socket

terminal from black (hot) wire on motor wire harness.

11. Attach the green ground wire from the motor wire harness and

the green ground wire from the cord set to the bottom right side

of the blower housing with (1) screw provided with the optional

blower.

12. With the heater standing upright, position the air discharge

opening of the blower housing downward. Place the bottom

ange of the blower housing over the top edge of the top heat

shield. Insert the blower housing into the top portion of the

heater by pivoting the blower housing upward 90°. Attach the

blower housing to the casing assembly with (4) screws provided

with the optional blower.

13. Grasp cord set at casing assembly back and pull excess cord

set through casing assembly back. Secure cord set in casing

assembly back with the strain relief provided with the optional

blower.

14. Installation of optional blower SRB-18T or SRB-30T is

completed.

15. If heater was removed from the wall, in order to install SRB-

18T or SRB-30T optional blower, check for gas leaks at all

gas connections before lower louver is replaced onto casing

assembly.

Attention! After optional blower has been installed use the following

steps to properly align the upper louver and the reector with

the heat shield.

A. When replacing upper louver, be sure the bottom lip of upper

louver goes behind the heat shield.

B. When replacing reector, be sure the top lip of reector goes

in front of the heat shield.

Excessive Blower Wheel Noise

ATTENTION! If your blower assembly develops a squeal, hum or

grinding noise, it indicates dirt or debris on shaft of blower wheel.

Use the following steps to clean shaft of blower wheel.

1. Remove red rubber grommet with brass bushing or black rubber

grommet with brass bushing from end of blower wheel shaft

opposite motor.

2. Clean blower wheel shaft with cotton cloth.

3. Place 1 or 2 drops of all purpose oil on END of blower wheel

shaft.

4. Replace red rubber grommet with brass bushing or black rubber

grommet with brass bushing onto end of blower wheel shaft.

Attention: The red rubber grommet with brass bushing or the

black rubber grommet with brass bushing must "snap-back"

into position.

5. Cleaning of blower wheel shaft is completed.

SRB-18T and SRB-30T

for Unvented Room Heaters BF-10, BF-20 and BF-30

HEAT SHIELD

FAN CONTROL BRACKET (BF-10 ONLY)

FAN CONTROL

GROUND WIRE SCREW

CORD SET HOLE IN

CASING BACK

REFLECTOR AND LOUVERS ARE

REMOVED FROM CASING ASSEMBLY

OPTIONAL BLOWER INSTALLATION INSTRUCTIONS

1 2 ... 12 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments

Empire Products BF-10-2 Owner's Manual Page 17

Comments to this Manuals

Related products and manuals for Fireplaces Empire Products BF-10-2